Notifications
Clear all

Project Violet – 2000 T4 2.5 Dayvan/Camper Restoration and Build

35 Posts
3 Users
8 Reactions
577 Views
Taspect-T4
(@taspect-t4)
Posts: 59
Established Member Member
Topic starter
 

The weather is causing havoc with progress at the moment as I just can’t seem to catch a break. I’ve two major jobs I need to get done in order to complete the work I am doing and unfortunately both of them require the use of a drill.

Job 1 is to drill through the roof and run the cables from the solar array into the van. This can then be finished off with a waterproof cowl and the isolator fitting in the back. Job 2 is to drill out the central bracket mount for the exhaust to install two M8 Rivnuts so I can mount the central exhaust hanger. The problem? Electricity and pouring rain isn’t the best combination. Everything is here, I have new bolts for the hanger, stainless steel rivnuts, 11mm drill bits, the waterproof cowl and rubber grommets for the cables, Tiger seal….literally everything, I just need that window to finish it all off.

As I am getting so frustrated with this, I have made an order for a brand new Bosch levelling valve for the rear and the correct master cylinder for the front. While the back end is right up in the air on ramps, that is the perfect time to get under there and replace the balancing valve. And should I get this window, then the exhaust takes priority, mounting the last two sections.

Next week it’s new rear callipers, discs and pads so that the entire braking system on the back end is brand new. With the new master cylinder as well, this should mean I can fully bleed the rear system, just requiring a quick run through once the front is done.

Really frustrated with it at the moment, all I want to do is finish some of these jobs off but the weather has other ideas unfortunately


 
Posted : October 21, 2026 5:00 am
Taspect-T4
(@taspect-t4)
Posts: 59
Established Member Member
Topic starter
 

FINALLY!!!! A window in the weather where it is (just) dry enough to get a drill down there. Work is manic so can’t take it any further, although I have had to order a new batch of stainless steel M8 rivnuts which are due tomorrow. Both old mounts have been drilled out now so it is purely mechanical work needed now to finish off the exhaust…

Also got a notification that the new Master Cylinder for the brakes is arriving today and the balancing valve is due tomorrow, so if I can get the exhaust done and buttoned up tomorrow, that then free’s me up to make a start on refreshing the braking system with all new parts.

Could it be? Could this bottle neck I’ve had finally be starting to unclog?


 
Posted : October 22, 2026 12:32 pm
Taspect-T4
(@taspect-t4)
Posts: 59
Established Member Member
Topic starter
 

The weather out there is horrific but I have so many jobs I have been waiting on either the weather, or parts, to finish off, for my own sanity I had to clear one of them off the list. Getting out in the week to drill out the old mounts for the exhaust has allowed me to crack on today and I can now say that I have a full stainless exhaust system fitted to the van. I need a final tweak to the end mount to raise it but about a centimetre to line it through perfectly with the bumper, but all the mounts are now replaced, she has a brand new catalytic converter on there and has a full exhaust system mounted.

Glad that job is out of the way, laying under the van in the wet with my glasses flipping up over my head every time I slightly tried to focus on what I was working on has not done my for my mood today!!

Next on the list is to start the brake refresh on the back. Not today though eh? Had a new balancing valve and master cylinder arrive so will be able to start cracking on with that next

But that’s me for the day. Time for a shower to get clean and warm up and a STRONG cup of coffee!!


This post was modified 3 weeks ago 4 times by Taspect-T4
 
Posted : October 24, 2026 11:55 am
Taspect-T4
(@taspect-t4)
Posts: 59
Established Member Member
Topic starter
 

Slowly but surely things are starting to come through now to refresh all the braking system. Haven’t had the cash recently to drop as much as I wanted through (had to buy three new snowboard setups and a washer dryer) so unfortunately parts for the van have come second…

However….

I have had the new master cylinder and brake compensator valve arrive, along with new discs, pads and callipers for the rear. This should give me what I need to refresh the rear and I’ll order the same for the front in the next few weeks. Rather than chasing faults around the van, a complete refresh seemed like a MUCH better idea.

Got out there this morning while the weather has held to start refreshing the back end. First job was to adjust the exhaust, the alignment was seriously tweaking my OCD so that is now level and aligned to the bumper. Much happier there. I can now say, with certainty, that job is ticked off the list.

While the van was up on the ramps however, it seemed like the perfect time to replace the balancing valve. I think I must have caught the van in a good mood as nothing snapped, every bolt came away nicely and the job didn’t fight me. The old was removed without any real trouble and the fresh unit installed. Last thing to get is a plastic nut for the level bar (although I might try 3D printing one in PETG as it isn’t a part that’s under load) and the valve is ready to bleed once the master cylinder and rear callipers are replaced


 
Posted : November 2, 2026 11:17 am
Taspect-T4
(@taspect-t4)
Posts: 59
Established Member Member
Topic starter
 

I’ve been a bit quiet on here just recently, combinations of reasons really, including poor weather, missing my MoT deadline, money being spent elsewhere. The usual life things really but I will admit that finding that list of assessed repairs needed did kinda steal the wind from my sail a bit. Still just as determined to make this our van but it’s a realisation that this is a far bigger mountain to climb than initially thought. That said, if I can complete all this work up to my own standards, then she is going to certainly have more than a little more life breathed into her and that is what has helped me regain my focus.

Obviously the first thing is to sort the brake system out and I am now starting on that. Still got this pile of parts to fit to her to refresh the back and the front braking will be ordered in a few weeks before a full bleed of the system. I could literally spend weeks/months chasing faults with the braking system which, according to this report, has various weak spots.

Give it a couple more weeks and I’ll get all the brake lines, callipers, discs and pads for the front of the van and once bled, I should be able to turn the van around ready to start tackling the welding. I need to buy the inner arch sections for the rear to order in a few weeks to finish stocking up on everything but then we can begin to get that done and signed off.

That’ll be it before Christmas then. With three kids all wanting presents, I have to put the van on hold. I’ll be sorting things out like custom designing a gauge pod for the front to 3D print, getting the bed completely stripped rear to weld, finish the solar install but I can’t get any new parts until the new year.

Forecasting forward though, even with the additional work, I am hoping to have the back insulated, boarded out, heating installed, the front retrimmed and the rock and roller installed, with an MoT by the first week of March, meaning we can at least use it for helping out the partners folks in Lancaster (We’ve nowhere to stay up there and have to help them rebuild their house so the van will be essential for that – It was one of many factors why I started – Her dad has very advanced Alzheimer’s and her mum is really struggling. Their house is literally falling down so I am working with a couple of Lads I know to start literally rebuilding their house almost from the ground up)

So progress will be slowing, money and weather at this time of the year but I’ll keep updating and moving this forwards as I can.


 
Posted : November 2, 2026 2:20 pm
Just T4s reacted
Page 3 / 3
Share: